Efficient Reduction of Food Related Mould Spores on Surfaces by Hydrogen Peroxide Mist.

The aim of the study was to evaluate the fungicidal effect of a H2O2 mist generating system for disinfection of spores of six food-related moulds (Alternaria alternata, Aspergillus flavus, Geotrichum candidum, Mucor plumbeus, Paecilomyces variotii, and Penicillium solitum) dried on stainless steel. Exposure to H2O2 mist for 2 or 4 h lead to >3 log reduction in mould spores in the majority of the tests. The presence of the soils 2% skim milk or 3% BSA did not significantly alter the fungicidal effect, while the presence of raw meat juice had an adverse fungicidal effect against Penicillium and Mucor in two out of three tests. Fungicidal suspension tests with liquid H2O2 confirmed the effectiveness of H2O2 on reducing the mould spores. Both the surface test and the suspension test indicated that P. variotii is more resistant to H2O2 compared to the other moulds tested. The study shows the efficiency of H2O2 mist on reducing food-related mould spores on surfaces.

Use of the selective agar medium CREAD for monitoring the level of airborne spoilage moulds in cheese production.

It was investigated if a selective medium for common cheese spoiling moulds (CREAD) could give more relevant information than a general mould medium in hygienic air-sampling in cheese factories. A total of 126 air-samples were taken in six Nordic cheese factories using the general mould medium DG18 and CREAD. The level and genera of air-borne mould was determined. Identification to species-level was performed for a selection of samples. In five cheese factories the mycobiota was dominated by Penicillium spp. and in one cheese factory by Cladosporium spp. The concentration of air-borne moulds varied between the cheese factories ranging from 1 to 270 cfu/m3 on DG18 with a median value of 17. The number of mould colonies was in general lower at CREAD. Identification indicated that CREAD supported growth of common spoilage moulds for cheese, such as Penicillium palitans and P. commune. The mycobiota on DG18 also consisted of moulds not commonly associated with spoilage of cheese, such as Cladosporium spp., P. brevicompactum and P. chrysogenum. Contamination of cheese with mould is periodically a problem in production of semi-hard cheese and the level of air-borne mould is therefore routinely monitored in cheese factories. A clear correlation between the total number of moulds in air and mould growth on products is not always found. The conclusion from the investigation is that it is recommended to use a selective medium for cheese spoilage moulds, such as CREAD in hygienic monitoring.

Mould contamination in production of semi-hard cheese.

Air, equipment, plastic film, brine and milk were sampled from four cheese factories in Norway during the period September 1997 to May 1999 in order to identify the critical points for mould contamination in the production process. Altogether, 672 samples were collected. Penicillium brevicompactum was the most frequently isolated species from three of the factories, while Geotrichum candidum was the most frequently isolated species from the fourth. P. commune, P. palitans, P. solitum and P. roqueforti ss. roqueforti, all common contaminants on cheese, were found in samples of air and equipment, and the former was also isolated from plastic film. The results in the present study showed that the mould levels in the cheese factories varied between the different control points. The mould levels at some of the air control points had high mould counts while the mould levels in milk and brine, on equipment and on plastic film, generally were low. The fungi at the control points with high mould levels consisted of common cheese contaminants as well as species not commonly isolated from cheese. The statistical analysis showed that air was the major source of the important cheese contaminants P. commune and P. palitans during the production process. High quality air with low number of cheese contaminants in production rooms, especially the wrapping room, is important in order to reduce mould contamination.